SIZE: SMG/KMG SMH/KMH
Load life, guaranteed with the rated rippple current applied
Non-solventproof. Solventproof type is available upon request. (~250V)
Item / Series | SMH |
KMH |
|||||||||||
Rated voltage range |
6.3 to 450 V |
6.3 to 450 V |
|||||||||||
Operating Temperature range | 6.3 to 100V: -40 to
+85ÞC 160 to 450V: -25 to +85ÞC |
6.3 to 100V: -40 to
+105ÞC 160 to 450V: -25 to +105ÞC |
|||||||||||
Capacitance Tolerance | +20% (M) (at 20ÞC, 120Hz) |
||||||||||||
Leakage current (20%) | 0.02CV (µA) or 3mA, whichever is smaller (after 5 minutes) | ||||||||||||
Where, | C: Nominal capacitance (µF) V: Rated working voltage (V) |
||||||||||||
tan ð | Rated voltage (V) | 6.3 | 10 | 16 | 25 | 35 | 50 | 63~100 | 160~250 | 315~450 | |||
tan ð | 0.60 | 0.50 | 0.40 | 0.30 | 0.25 | 0.20 | 0.15 | 0.10 | 0.15 | ||||
* : 0.15max. for 35mm diameter (at 20ÞC, 120Hz) |
|||||||||||||
Low temperature Characteristics | Impedance ratio at 120 Hz between the -25ÞC or -40ÞC value and 20ÞC value shoul not exceed the values given below | ||||||||||||
Rated Voltage (V) | 6.3~16 | 25 | 35 | 50,63 | 80,100 | 160~400 | 450 | ||||||
Z at -25ÞC/Z at +20ÞC | 4 | 3 | 3 | 2 | 2 | 4 | 8 | ||||||
Z at -40ÞC/Z at +20ÞC | 15 | 10 | 8 | 6 | 5 | - | - | ||||||
Load life with the rated ripple current applied | After the capacitors are
subjected to DC voltage with the rated ripple current applied for 2,000 hours at the
maximum rated operating temperature, the following specifications should be satisfied when
the capacitors are restored to 20ÞC The sum of DC voltage and peak AC voltage must not exceedthe full rated voltage of the capacitor. |
||||||||||||
Capacitance Change | =>+20% of the initial measured value | ||||||||||||
tan ð | =< 200% of the initial specified value | ||||||||||||
Leakage current | =< The initial specified value | ||||||||||||
Shelf Life | The following specifications
shall be satisfied when the capacitors are restored to 20ÞC after exposing them at
maximum operating temperature for 1,000 hours without voltage applied. The rate working voltage should be applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not more than 48 hours before the measurements. |
||||||||||||
Capacitance Change | =>+20% of the initial measured value | ||||||||||||
tan ð | =< 150% of the initial specified value | ||||||||||||
Leakage current | =< The initial specified value | ||||||||||||
Others | Satisfies characteristics W of JIS C 5141 |
Frequency / Rated Voltage | 50Hz | 120Hz | 300Hz | 1KHz | 10KHz | 100KHz |
6.3~50V | 0.95 | 1.00 | 1.03 | 1.05 | 1.08 | 1.08 |
63~100V | 0.92 | 1.00 | 1.07 | 1.13 | 1.19 | 1.20 |
160~250V | 0.81 | 1.00 | 1.17 | 1.32 | 1.45 | 1.50 |
315~450V | 0.77 | 1.00 | 1.16 | 1.30 | 1.41 | 1.43 |
Ambient Temperature (CÞ) | 65Þ | 85 | 105 |
SMH-Multiplier | 1.23 | 1.00 | - |
KMH-Multiplier | 1.75 | 1.00 |
Note: For long life applications do not exceed rated ripple current specified at the maximum operating temperature or at lower
STANDARD RATINGS SMHSize DxL (mm) | 100V |
160V |
180V |
200V |
250V |
|||||
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
|
22x25 | 820 | 1.86 | 330 | 1.40 | 270 | 1.27 | 270 | 1.27 | 180 | 1.04 |
x30 | 1,200 | 2.09 | 470 | 1.73 | 390 | 1.58 | 330 | 1.45 | 270 | 1.31 |
x35 | 1,500 | 2.41 | 560 | 1.95 | 470 | 1.79 | 470 | 1.78 | 330 | 1.49 |
x40 | 1,800 | 2.71 | 680 | 2.21 | 560 | 2.00 | 560 | 2.00 | 390 | 1.67 |
x45 | 2,200 | 3.08 | 820 | 2.49 | 680 | 2.27 | - | - | 470 | 1.88 |
x50 | - | - | 1,000 | 2.82 | 820 | 2.55 | 680 | 2.33 | - | - |
25.4x25 | 1,200 | 2.10 | 470 | 1.74 | 390 | 1.58 | 390 | 1.58 | 270 | 1.32 |
x30 | 1,500 | 2.43 | 680 | 2.16 | 560 | 1.96 | 470 | 1.80 | 330 | 1.51 |
x35 | 1,800 | 2.75 | 820 | 2.45 | 680 | 2.23 | 560 | 2.03 | 470 | 1.86 |
x40 | 2,200 | 3.13 | 1,000 | 2.79 | 820 | 2.53 | 680 | 2.30 | 560 | 2.09 |
x45 | 2,700 | 3.57 | 1,200 | 3.15 | 1,000 | 2.87 | 820 | 2.60 | - | - |
x50 | 3,300 | 4.06 | - | - | - | - | 1,000 | 2.95 | 680 | 2.44 |
30x25 | 1,500 | 2.46 | 680 | 2.19 | 560 | 1.99 | 560 | 2.00 | 390 | 1.66 |
x30 | 2,200 | 3.09 | 820 | 2.50 | 820 | 2.50 | 680 | 2.28 | 470 | 1.89 |
x35 | 2,700 | 3.55 | 1,200 | 3.13 | 1,000 | 2.86 | 820 | 2.59 | 560 | 2.14 |
x40 | 3,300 | 4.05 | - | - | 1,200 | 3.23 | 1,000 | 2.95 | 680 | 2.43 |
x45 | 3,900 | 4.54 | 1,500 | 3.73 | - | - | 1,200 | 3.31 | 820 | 2.75 |
x50 | 4,700 | 5.13 | 1,800 | 4.20 | 1,500 | 3.83 | - | - | 1,000 | 3.31 |
35x25 | 2,200 | 3.14 | 1,000 | 2.80 | 820 | 2.53 | 680 | 2.31 | 560 | 2.06 |
x30 | 2,700 | 3.71 | 1,200 | 3.27 | 1,000 | 2.95 | 1,000 | 2.95 | 680 | 2.46 |
x35 | 3,900 | 4.49 | 1,500 | 3.69 | 1,200 | 3.31 | 1,200 | 3.31 | 820 | 2.77 |
x40 | 4,700 | 5.11 | 1,800 | 4.18 | 1,500 | 3.82 | 1,500 | 3.82 | 1,000 | 3.32 |
x45 | 5,600 | 5.75 | 2,200 | 4.78 | 1,800 | 4.32 | 1,800 | 4.32 | 1,200 | 3.53 |
x50 | - | - | 2,700 | 5.45 | 2,200 | 4.92 | 2,200 | 4.92 | 1,500 | 4.04 |
Size DxL (mm) |
315V |
350V |
400V |
450V |
||||
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
Capacitance (µF) |
Ripple Current (A rms) 85ÞC,120Hz |
|
22x25 | 120 | 0.94 | 100 | 0.86 | 82 | 0.78 | 56 | 0.65 |
x30 | 150 | 1.11 | 120 | 0.99 | 100 | 0.90 | 82 | 0.82 |
x35 | 180 | 1.20 | 150 | 1.14 | 120 | 1.02 | 100 | 0.93 |
x40 | 220 | 1.41 | 180 | 1.28 | 150 | 1.16 | 120 | 1.04 |
x45 | 270 | 1.60 | 220 | 1.44 | 180 | 1.31 | 150 | 1.19 |
x50 | 330 | 1.82 | 270 | 1.64 | 220 | 1.49 | - | - |
25.4x25 | 150 | 1.10 | 120 | 0.99 | 100 | 0.90 | 82 | 0.82 |
x30 | 220 | 1.38 | 180 | 1.24 | 150 | 1.14 | 120 | 1.02 |
x35 | 270 | 1.59 | 220 | 1.44 | 180 | 1.30 | 150 | 1.19 |
x40 | 330 | 1.80 | 270 | 1.63 | 220 | 1.47 | 180 | 1.33 |
x45 | 390 | 2.01 | - | - | 270 | 1.67 | - | - |
x50 | - | - | 330 | 1.88 | - | - | 220 | 1.54 |
30x25 | 220 | 1.40 | 180 | 1.27 | 150 | 1.16 | 120 | 1.03 |
x30 | 270 | 1.59 | 220 | 1.44 | 180 | 1.44 | 150 | 1.19 |
x35 | 390 | 1.99 | 270 | 1.66 | 270 | 1.66 | 180 | 1.35 |
x40 | 470 | 2.27 | 390 | 2.06 | 330 | 1.90 | 220 | 1.55 |
x45 | 560 | 2.56 | - | - | 390 | 2.13 | 270 | 1.78 |
x50 | - | - | 470 | 2.40 | - | - | 330 | 2.01 |
35x25 | 330 | 1.80 | 270 | 1.63 | 220 | 1.47 | 180 | 1.33 |
x30 | 470 | 2.23 | 330 | 1.87 | 330 | 1.87 | 220 | 1.53 |
x35 | 560 | 2.49 | 470 | 2.33 | 390 | 2.08 | 270 | 1.73 |
x40 | 680 | 2.87 | 560 | 2.60 | 470 | 2.39 | 330 | 2.0 |
x45 | 820 | 3.25 | 680 | 2.96 | 560 | 2.69 | 390 | 2.24 |
x50 | - | - | - | - | - | - | 470 | 2.53 |
© 1998, Russell Industries, Inc.
and its affiliated Companies. All Rights Reserved.
This Page was last modified on Wednesday, March 27, 2002.